Bidet 3 User Manual: Flip, Shower & Deluxe
Flip · Shower · Deluxe
Bidet 3 user guide
From your first rinse to everyday care. These operating instructions apply to all three editions.
Shower Edition
Focus + Wide showerheads. Focus and Wide showerheads for two spray patterns.
Your nozzle instructions
Deluxe Edition
Flip head + Focus + Wide showerheads. Flip head and both showerheads in one set.
Your nozzle instructionsOn this page
01
Ready for your first rinse
1. Fill
Fill a compatible bottle with clean water. Maximum 40°C / 104°F.
2. Attach
Screw the main unit onto the bottle clockwise. Use the adapter if required.
3. Start
Press the button once to start in Low mode.
4. Position
Adjust the nozzle angle for external rinsing from the front or back.
Use clean water at or below 40°C (104°F). For external use only. Do not insert the nozzle for internal rinsing.
02
Power & pressure
| What you want to do | Press the button |
|---|---|
| Start in Low mode | Press once while the unit is off. |
| Switch from Low to High | Press again within 3 seconds of starting. |
| Stop from Low mode | Once more than 3 seconds have passed, press once. |
| Stop from High mode | Press once. |
The unit automatically stops after about 3 seconds if no water is detected. Refill the bottle before starting again.
03
Charging & indicator lights
Connect a USB Type-C charging cable to the charging port. Use a supply that matches the rating on the unit: 5 V DC, 0.5 A. Charging takes about 2.5 hours.
| Indicator | What it means |
|---|---|
| Flashing light | Charging. |
| Light stays on | Charging is complete. |
| Red light | Low battery. Recharge the unit. |
04
Find your nozzle instructions
| Edition | Nozzles supplied | Instructions |
|---|---|---|
| Flip | Fold-out Flip head | Install and use the Flip head |
| Shower | Focus and Wide showerheads | Change a showerhead |
| Deluxe | Flip head, Focus and Wide showerheads | Flip head · Showerheads |
The bottle adapter and Gravity Ball Bottle have their own accessory instructions.
05
Keep the water flowing
The inlet filter is at the bottom of the main unit. If the water flow becomes weak, gently clean this filter.
- Moisten a cotton swab with clean water.
- Gently rotate it against the filter to remove residue.
- Use light pressure. Excessive force can damage the filter.
The filter can be cleaned without removing it or taking the main unit apart.
The main unit has an IPX7 waterproof rating and can be rinsed with water. Use clean water; do not use medicinal solutions or cloudy liquids.
06
Troubleshooting
Why is the water flow weak?
Check the inlet filter for residue and clean it gently with a damp cotton swab. If the indicator is red, recharge the unit.
Why does the bidet stop by itself?
The unit stops if no water is detected for about 3 seconds, if the battery is low, or if the inlet filter is clogged. Refill the bottle, check the indicator, and clean the filter as needed.
How do I turn it off?
In Low mode, press once after the first 3 seconds. In High mode, press once. Pressing within the first 3 seconds of Low mode switches to High.
Can I use a phone charger?
Use a USB Type-C cable and a supply that matches the unit’s input rating: 5 V DC, 0.5 A.
Why do a few drops drip out while it is off?
A few drops may drip when the unit is held upside down, due to water pressure. The original manual identifies this as normal.
How long can it run on a full charge?
The original manual lists approximately 40 minutes of continuous use after a full charge.
What if it still does not work?
Email [email protected] with your purchase channel, order number and a description of the problem.
07
Before every use
- Use clean water no hotter than 40°C (104°F). Do not place the bottle in hotter water.
- For external use only. Do not insert the nozzle for internal rinsing.
- Children must use the product under adult supervision.
- Avoid drops, impacts and rubbing against hard objects.
- Do not open, squeeze, burn or heat the product above 40°C (104°F).
- Do not use medicinal solutions or cloudy liquids.
- Only use a safety extra-low-voltage power supply corresponding to the marking on the appliance.
08
Technical specifications
| Item | Specification |
|---|---|
| Product | Insolife Bidet 3 |
| Main unit size | 35 mm diameter × 97 mm height |
| Main unit weight | Approximately 80 g |
| Input | 5 V DC, 0.5 A |
| Charging port | USB Type-C |
| Charging time | Approximately 2.5 hours |
| Battery | 350 mAh rechargeable lithium battery |
| Waterproof rating | IPX7 |
| Bottle capacity | 400 mL |
| Materials | ABS main unit shell; polypropylene bottle |
Specifications follow the supplied English user manual. Package contents vary by edition.
09
Download & warranty
Keep a copy of the English manual for offline reference. The PDF covers the main unit, nozzle installation, bottle adapter, care and safety.
Warranty service is provided for 12 months from the date of purchase. Include your purchase channel, order number and a description of the issue when contacting support.